toggle quoted messageShow quoted text
No worries Dave, I found the 328P’s on ebay from an American seller with the Arduino R3 boot loader installed. I ordered 3, I think they were around $5.00 each
+ a few bucks shipping. I really don’t care about the different Iambic settings as I am a single lever guy. I built a simple Iambic to single lever converter using a CMOS quad NOR chip and a couple of BS170’s which I put in an Altoids tin and power from a
9 volt battery. Programming the micro just gives me something new to learn.
From: HilltopperKit@4SQRP.groups.io [mailto:HilltopperKit@4SQRP.groups.io]
On Behalf Of Dave Benson
Sent: Wednesday, July 25, 2018 5:22 AM
To: firstname.lastname@example.org; HilltopperKit@4sqrp.groups.io
Subject: Re: [HilltopperKit] [4SQRP] Hilltopper
(still inhaling the first cup of coffee here)
DigiKey also carries the bootloaded version. At least with them, searching on 'Arduino' ensures that you're getting the right version.
To my knowledge, the '328 doesn't work directly in the Arduino IDE, although the '328P is fine. The difference is in a table of fuse settings. It's possible to modify the table to make it work. There's information on the Arduino forums,
but for my money, simply ordering the right one makes more sense.
On Tue, Jul 24, 2018 at 9:37 PM, John Lonigro <jonigro@...> wrote:
I know Jameco sells the ATMega328P both with and without the bootloader. I don't know if Mouser does or not. The one with the bootloader already burned in is a little more expensive, but I suspect it isn't very difficult to load yourself. The Arduino IDE
has an option under "Tools" labeled "burn bootloader". I haven't done this myself yet, but it looks pretty straightforward. Good luck.
On 07/24/2018 03:40 PM, John T. Fitzer wrote:
Good afternoon Dave, I have a question about the ATmega328P-PU micro available from Mouser. I would like to purchase another micro chip and load the latest version of the firmware
using an Arduino uno to program the new chip. My question is, does the micro as supplied from Mouser have the boot loader already installed or will I have to burn that first prior to downloading the sketch? I have played with Arduino a little but I am no programmer
by any stretch of the imagination. I think the first thing I would do is to download the latest version of the IDE. I know there is a way to burn the boot loader in the IDE but I have never done it so it will be an adventure. If the chips from Mouser do not
have the boot loader installed, is there a source for the chips that do have it installed? In addition I have several 328 chips that I purchased several years ago that do have the boot loader already burned in. These are not the P (pico power) version. Will
the non p 328 chips work in the hill topper at a slightly increased current drain, or is there something in the program that would prevent them from operating correctly? P.S. The rig works great, except the BFO is a bit low but workable I just have to tune
the other station in at around 550 hz or so so I will be zero beat. I double checked the caps in the BFO circuit and they seem correct. When I get time I may try removing the 10 pf cap across the trimmer and see what happens. That may give me enough increase
in frequency. If not I’ll replace the trimmer with a 3 to 30 pf unit. I’m sure that will work.
From: John T. Fitzer
Sent: Thursday, July 05, 2018 9:00 AM
GM Dave and all in the group. I took a couple days off to extend the 4th holiday and used some of the time to build the Hilltopper kit. I followed the manual verbatim,
doing each section in sequence. I was rewarded with a radio that worked the first time it was powered up. The only hitch and it was a small one was that my kit only had approximately 12 inches of #24 magnet wire, while 22 inches minimum is required. For me
this was no big deal as I keep rolls of magnet wire in various sizes on hand for homebrew projects. The rig puts out 5.4 watts with a 13 volt power supply. Not bad. The frequency calibration and BFO set up went fine. I put the rig on the air yesterday operating
portable from my back yard. I had several nice contacts including one DX contact. I used the Hilltopper with a Four States tuner feeding a 20 meter ENFW vertical supported on a Sota Beams 30 ft. travel mast. I also connected my Hipermite audio filter to test
and make sure it would play nice with the Hilltopper. All in all I must say I’m impressed with the quality of the kit. It is very well designed, and the parts are of good quality and fit. The manual is very well written, and does point out possible glitches
that a new builder may encounter. Again I would like to thank Dave and all who helped make this a great kit and for making it available for the ham QRP community at a very reasonable price. Great job all. I will not be available for the next couple of weeks
as I will be in the field working on medium voltage high power circuit breakers. These are the opposite of QRP, 350 MVA @ 5kv 3 phase power. I will have my QRP portable go bag with me if I get some free time to operate at the hotel. 72’s for now W3BNO.
On Behalf Of Dave Benson
Sent: Monday, July 02, 2018 5:43 AM
Subject: Re: [4SQRP] Ozark Patrol C6 & C13 Capacitors
It shouldn't matter- consider them interchangeable.
On Sun, Jul 1, 2018 at 10:02 PM, Dave TRX via Groups.Io <w5trx_dave@...> wrote:
C6 and C13 both require a 1m eletrolytic cap. The two that came in my kit are 50v and 100v and the spec
doesn't say which to use where, so can someone tell me which one goes to C6 and C13?