40 METERS WA9PWP PAUL N4ELM DAVE NK8O CHARLES N0XM MIKE N4MJ GLENN N4DR MARC K9ZTV KENT KG5UK BRAD W2SH CHAS 80 METERS N4ELM DAVE NK8O CHARLES N0XM MIKE K9ZTV KENT N4MJ GLENN WA9PWP PAUL DELTA MIKE

Wednesday Evening 40 and 80 meter Nets When: 10/05/2022 20:00 to 21:00 (UTC-05:00) America/Chicago Where: 40 and 80 Meters Organizer: jomatlock@... View Event Description: The 40 Meter

I didn't adjust any of these and so far it seems to work fine. Here's another question... Since we've been told on numerous kits to turn such-and-such fully counter clockwise.... Why can't these

Good afternoon Bert N0YJ will be your NCS for the 40 and 80 meter nets tonight. Thanks 73 Johnny ACØBQ -- Check out the 4SQRP website at 4sqrp.com

Reminder: Wednesday Evening 40 and 80 meter Nets When: 10/05/2022 20:00 to 21:00 (UTC-05:00) America/Chicago Where: 40 and 80 Meters Organizer: jomatlock@... View Event Description: The

Reminder: Wednesday Evening 40 and 80 meter Nets When: 10/05/2022 20:00 to 21:00 (UTC-05:00) America/Chicago Where: 40 and 80 Meters Organizer: jomatlock@... View Event Description: The

Reminder: Wednesday Evening 40 and 80 meter Nets When: 10/05/2022 20:00 to 21:00 (UTC-05:00) America/Chicago Where: 40 and 80 Meters Organizer: jomatlock@... View Event Description: The

Think of these trimmers within each capacitor as a fine adjustment. They set the minimum capacitance of the front panel adjustable value.

On page 11: ( ) Set the trimmers to minimum, i.e., unmeshed as shown in Photo 17. There are two trimmers on each polyvaricon variable capacitor. I notice that Photo 17 referenced on page 11 shows an

OK, I see it says adjust to minimum - but what does that mean? Min capacitance? And where should the large varcap be while doing this full open, lowest value capacitance or full closed highest cap

It’s difficult to see without intense light, but if you look carefully at the meshing components as you turn the screw, you can see when they fully unmesh by paying attention to the shadow looking

Greetings David, I have an SS-40Tx board in my stash, as I'm the designer. I will send it to you if you pass along your mailing address. You would be on the hook to find all the

This is not adjusting C3 and C4. It is adjusting the trimmers built into polyvaricons C3 and C4 - page 11 of the assy instructions and refers to "photo 17". Fortunately, my C3 and C4 matched photo

You are tuning for max noise right? First C3 then C4 AFTER you tune for max noise using the inductor switch with both caps set to half-way position? -- 73 de KE3FL Phil

John, Im actually looking for the ss-40 transmitter the mate to the ss-40 receiver, not the ns-40 The receiver i have is this:K8IQY SS-40 Stable and Sensitive 40M Receiver Four State QRP Group Four

A quick chole that works for me is using a FT240-43 toroid and your coax. I first found it in this article. When using an EFHW where you want your coax to work as a counterpoise I put it close to

Greetings David, I may have an SS-40Tx board somewhere in my stash, as I'm the designer. If I can find one, I will send it to you if you pass along your mailing address. You would

I think I do still have a partially-assembled NS-40 in my to-do pile. I bought it years ago originally intending to also buy the receiver and Magic Box, but with the latter kits being retired in the

I can't figure this one out. Not sure if I'm trimming C3 or C4 or both, and can't tell what minimum is. The varicons that came with my kit are not the ones pictured in the guide so I can't just ape

hello, Im looking for the mate transmitter for the ss-40 receiver. I purchased the receiver but need the transmitter. Anyone have one they havent built? wanting to get rid of one cheap? let me know