NJQRP Skeeter Hunt - If you snooze .....
If you snooze, you lose! DON'T BE LEFT OUT! If you partook - send in your score and comments.
Log submissions are due by Midnight of Labor Day, September 3rd. That's THIS Monday night. You don't have to submit your entire logs - just a summary - follow this example Larry - W2LJ - NJ Skeeter #13 - All CW Single Op Skeeter QSOs - 23 Non-Skeeter QRP QSOs - 5 Non-Skeeter QRO QSOs - (if any) S/P/Cs - 18 Station Class Multiplier X4 Water Bonus - 100 points Please send it to w2ljqrp@gmail.com I will answer each log submission with an e-mail veifying your entry. If you don't hear from me - try again. The Scoreboard and comments will be posted Tuesday evening. 72 de Larry W2LJ NJQRP Skeeter Hunt Manager
|
|
Upcoming Event: Wednesday Evening 40 and 80 meter Nets - Wed, 08/14/2019 8:00pm-9:00pm
#cal-reminder
main@4SQRP.groups.io Calendar <main@...>
Reminder: Wednesday Evening 40 and 80 meter Nets When: Wednesday, 14 August 2019, 8:00pm to 9:00pm, (GMT-05:00) America/Chicago Where:40 and 80 Meters Organizer: jomatlock@... Description: The 40 Meter Net will be at 8:00 pm DST central time on 7.122 +-. QRM
|
|
Re: working on alignment hilltopper 20
KM6KJE
I found the page for diodes, transistors, ic's sorry just did not read enough but still need the missing parts
On Monday, August 12, 2019, 12:47:19 PM PDT, KM6KJE <terry.schulz@...> wrote:
Nouveau-75 QRP I am missing two components c4 and rrr and the pages for the rest of the smt install only have resistors and capacitors nothing about transistor SMT's diodes and ic's I would like to test each before I start build thanks terry
On Tuesday, January 29, 2019, 08:10:21 PM PST, KM6KJE <terry.schulz@...> wrote:
thanks, I got it
On Tuesday, January 29, 2019, 6:35:12 PM PST, Dave Benson <davek1swl@...> wrote:
Terry- Your frequency counter connects to the center pin of the BNC connector (J1). The counter's ground lead can be clipped to the BNC connector's shell. When you power up with the jumper installed, the Hilltopper transmits for 5 seconds. During that time, you turn the tuning knob to bring the frequency to 14060 kHz. - Dave, K1SWL On Tue, Jan 29, 2019 at 7:40 PM KM6KJE <terry.schulz@...> wrote: I was wondering what the center pin was to hook up a frequency counter to the section is alignment the CAL placement pin has only two pins thanks
|
|
Re: Nouveau 75 Errata
nm0s_qrp <ai9e_qrp@...>
One of my priority items for this week is to compile a troubleshooting guide with expected voltages. You'll see it hopefully by the end of the week. 73 Dave
|
|
Re: working on alignment hilltopper 20
KM6KJE
Nouveau-75 QRP I am missing two components c4 and rrr and the pages for the rest of the smt install only have resistors and capacitors nothing about transistor SMT's diodes and ic's I would like to test each before I start build thanks terry
On Tuesday, January 29, 2019, 08:10:21 PM PST, KM6KJE <terry.schulz@...> wrote:
thanks, I got it
On Tuesday, January 29, 2019, 6:35:12 PM PST, Dave Benson <davek1swl@...> wrote:
Terry- Your frequency counter connects to the center pin of the BNC connector (J1). The counter's ground lead can be clipped to the BNC connector's shell. When you power up with the jumper installed, the Hilltopper transmits for 5 seconds. During that time, you turn the tuning knob to bring the frequency to 14060 kHz. - Dave, K1SWL On Tue, Jan 29, 2019 at 7:40 PM KM6KJE <terry.schulz@...> wrote: I was wondering what the center pin was to hook up a frequency counter to the section is alignment the CAL placement pin has only two pins thanks
|
|
Re: Nouveau 75 Errata
K4ENC
HI DAVE 7.1 V ACROSS R39 NOTHING TO GR. ----------------------------------------- From: "Dave Benson"To: main@4sqrp.groups.io Cc: Sent: Monday August 12 2019 1:16:47PM Subject: Re: [4SQRP] Nouveau 75 Errata
The voltage across R39 (10K) should be 0V in receive. You also want to verify
the resistance to ground there (w/ power removed) in case there's a short somewhere.
- Dave, K1SWL
|
|
Re: Nouveau 75 Errata ATT DAVE NM0S
K4ENC
q 11 HOT ON REC q 12 COOL ON REC q 11 GATE 7.8 V q 12 GATE 12.7 ----------------------------------------- From: "K4ENC"To: "main@4SQRP.groups.io" Cc: Sent: Monday August 12 2019 11:20:28AM Subject: Re: [4SQRP] Nouveau 75 Errata Looking some volt reading around Q11 and D 6……………….Q11 running very hot in rec. Bob
Sent from Mail for Windows 10
|
|
Re: Nouveau 75 Errata
Bill VanKirk
I noted in the manual L-2 shows 17T and L-4 18T. The schematic shows L-2 16T and L-4 16T. Which one is correct? Thanks! Bill -- Bill W0PT
|
|
SARK-110 I had for sale
It sold quick -- The SARK-110 analyzer has been SOLD and shipping in a few minutes.
Jim, W0EB
|
|
OT: FS Sark-110 Super Antenna Analyzer
Thanks for the interest, this has been SOLD.
W0EB
|
|
Re: Nouveau 75 Errata
nm0s_qrp <ai9e_qrp@...>
If there is heating in Q11 during receive, that suggests there may be leakage in Q12. Is it getting warm as well? Check the gate voltages of both Q11 and Q12 during receive, and make sure they are not being turned on. 73 Dave NM0S
|
|
Low cost Visor Magnifier even lower cost
The former low cost Visor Magnifier that I notified everyone about previously is now available from American Science & Surplus for the low cost of $7.95 each. I bought one for my grandson and then ordered another one for me as a back up to take to buildathons..... nothing lost if lost or given away. See sciplus.com and go to Headband Magnifying Visor. There is also a 15% discount for signing up with them. What a deal! I have no affiliation with this company, just a happy purchaser in the past. Dave K8WPE
|
|
Re: Nouveau 75 Errata
Dave Benson
The voltage across R39 (10K) should be 0V in receive. You also want to verify the resistance to ground there (w/ power removed) in case there's a short somewhere. - Dave, K1SWL
|
|
Re: Nouveau 75 Errata
K4ENC
Looking some volt reading around Q11 and D 6……………….Q11 running very hot in rec. Bob
Sent from Mail for Windows 10
|
|
Send in your SSS score
John Lonigro
Folks:
I am extremely busy this month. It would help immensely if I could tabulate the scores by tomorrow (Tuesday) morning. So please submit your SSS score by the end of today. Thanks and 72, John, AA0VE 4SQRP Contest Coordinator
|
|
Re: Nouveau 75 Errata
K4ENC
IT STARTS HEATING UP AS SOON AS U FLIP THE SW.....DIDNT NOTICE IT WITH THE FIRST CONTACE RIGHT OFF...TO EXCITED THAT IT WAS WORKING?? BOB ----------------------------------------- From: "K4ENC"To: main@4SQRP.groups.io Cc: Sent: Sunday August 11 2019 2:22:14PM Subject: Re: [4SQRP] Nouveau 75 Errata Got the info and corrected my build but now have a heat problem with q 11 in rec. made a contact with it and told it sounds great...any suggestions on the heat issue
|
|
4SQRP Second Sunday Sprint - Sun, 08/11/2019
#cal-notice
main@4SQRP.groups.io Calendar <noreply@...>
4SQRP Second Sunday Sprint When: Organizer: Description:
|
|
Re: Items for sale
Charles Vinson
Hey Author Did you sell everything? Chuck kf6fju Powered by Cricket Wireless.
-------- Original message -------- From: Arthur Prior <fulltimerart@...> Date: 08/11/2019 5:25 AM (GMT-08:00) To: main@4SQRP.groups.io Subject: [4SQRP] Items for sale We have gone back to the RV lifestyle and space is limited so I have to pass on some of my goodies. All prices are "O B O" and shipping is not included, all items are in very good shape except #1, and I can email pictures. #1, 1922 Radiant 1 tube radio-looks complete, needs some rewiring and coils rewound. $25.00. #2 Ten Tec # 1253 9 band SW rcvr-looks and works great. $60.00 #3 Murania, works great, $25.00. #4 Complete "Breadboard" radio with xcvr, cw filter and antenna tuner on a finished 9x12 board. also has a powered speaker, small storage box with extra xtals and a "night sender" key. $90.00. #5 Bayou Jumper in box (green board) with several extra xtals. $75.00. #6 N3ZI compact counter, $15.00 #7, NS 40 set up with wood cabinet, rcvr in own wood cabinet but can be installed in cabinet with other 2 units, in nice shape but needs wiring together. $100.00
|
|
Bob
K4ENC
Care less about GA but need some help with my nouveau 75 and don't know if this is the right place to ask for help??radio works been told sounds great
rx tx not tracking but the biggie id q11 running really really hot in rec...………….any suggestions 73
|
|
Re: Nouveau 75 Errata
K4ENC
Got the info and corrected my build but now have a heat problem with q 11 in rec. made a contact with it and told it sounds great...any suggestions on the heat issue
|
|