|
source code
I just applied says have to wait for acceptance.
I just applied says have to wait for acceptance.
|
By
KM6KJE
· #23376
·
|
|
source code
Where can I find the source code for the hill topper 30? thanks, terry
Where can I find the source code for the hill topper 30? thanks, terry
|
By
KM6KJE
· #23374
·
|
|
hill topper 30 not working
everything works so far Jim replaced the ic av and I tested it with the jumper in at startup and I get a sidetone and on transmission, the light turns on with a 50-ohm load that I made that's about al
everything works so far Jim replaced the ic av and I tested it with the jumper in at startup and I get a sidetone and on transmission, the light turns on with a 50-ohm load that I made that's about al
|
By
KM6KJE
· #23346
·
|
|
hill topper 30 not working
thanks, terry
By
KM6KJE
· #23331
·
|
|
hill topper 30 not working
I put together a hill topper 30 as I have put together a few of them on startup with a jumper on CAL all I get is a hum no sidetone it transmits but the signal is a hum no sidetone does anyone have id
I put together a hill topper 30 as I have put together a few of them on startup with a jumper on CAL all I get is a hum no sidetone it transmits but the signal is a hum no sidetone does anyone have id
|
By
KM6KJE
· #23275
·
|
|
Soldering Iron Temperature
try an infrared gun to check the temp tip of your gun
try an infrared gun to check the temp tip of your gun
|
By
KM6KJE
· #23096
·
|
|
nouveau 75 Dave Cripe/Voltage Checks
thank you thank you its a start terry
thank you thank you its a start terry
|
By
KM6KJE
· #20683
·
|
|
nouveau 75 Dave Cripe
Hi, dave do you have a list of voltages that the transistors are supposed to be I installed the new module and the reception is still bad and on Q1 is there suppose to be connectivity from the middle
Hi, dave do you have a list of voltages that the transistors are supposed to be I installed the new module and the reception is still bad and on Q1 is there suppose to be connectivity from the middle
|
By
KM6KJE
· #20675
·
|
|
nouveau 75
thank you, Dennis, I have one other question and that is I was sent a module and I built it and installed it but the reception is still bad it sounds like it is out of frequency I know on my big rig i
thank you, Dennis, I have one other question and that is I was sent a module and I built it and installed it but the reception is still bad it sounds like it is out of frequency I know on my big rig i
|
By
KM6KJE
· #20631
·
|
|
nouveau 75
Hi I have one more question to ask and that is what gauge wire is used for the toroids T50-2 and T50-6. Kit Nouveau 75, is it #22 gauge magnet wire? thanks, terry
Hi I have one more question to ask and that is what gauge wire is used for the toroids T50-2 and T50-6. Kit Nouveau 75, is it #22 gauge magnet wire? thanks, terry
|
By
KM6KJE
· #20627
·
|
|
nouveau 75
should I rewind them
By
KM6KJE
· #20626
·
|
|
nouveau 75
Hi, joe I have recently built the nouveau 75 and I have installed the new board you sent me. it seems like it needs a fine tune adjustment but that's what I am writing about it's that when I use the t
Hi, joe I have recently built the nouveau 75 and I have installed the new board you sent me. it seems like it needs a fine tune adjustment but that's what I am writing about it's that when I use the t
|
By
KM6KJE
· #20624
·
|
|
Nouveau 75
Hi, joe I have recently built the nouveau 75 and I have installed the new board you sent me. it seems like it needs a fine tune adjustment but that's what I am writing about it's that when I use the t
Hi, joe I have recently built the nouveau 75 and I have installed the new board you sent me. it seems like it needs a fine tune adjustment but that's what I am writing about it's that when I use the t
|
By
KM6KJE
· #20621
·
|
|
working on alignment hilltopper 20
I found the page for diodes, transistors, ic's sorry just did not read enough but still need the missing parts
I found the page for diodes, transistors, ic's sorry just did not read enough but still need the missing parts
|
By
KM6KJE
· #20267
·
|
|
working on alignment hilltopper 20
Nouveau-75 QRP I am missing two components c4 and rrr and the pages for the rest of the smt install only have resistors and capacitors nothing about transistor SMT's diodes and ic's I would like to te
Nouveau-75 QRP I am missing two components c4 and rrr and the pages for the rest of the smt install only have resistors and capacitors nothing about transistor SMT's diodes and ic's I would like to te
|
By
KM6KJE
· #20265
·
|
|
New Kit ?
How do you order? I would like one
How do you order? I would like one
|
By
KM6KJE
· #19919
·
|
|
problem with Si5351
no, I do not also pin o on the Si5351 should have around 1.86 volts has no voltage the rest of the pins fine
no, I do not also pin o on the Si5351 should have around 1.86 volts has no voltage the rest of the pins fine
|
By
KM6KJE
· #19314
·
|
|
problem with Si5351
the Si5351 0 pin as no voltage it should be about 1.68 volts and I am not getting any audio any suggestions on fixing this. all the rest of the pins on the Si5351 are right. thank you
the Si5351 0 pin as no voltage it should be about 1.68 volts and I am not getting any audio any suggestions on fixing this. all the rest of the pins on the Si5351 are right. thank you
|
By
KM6KJE
· #19312
·
|
|
Hilltopper 40
Hilltoppers 40 not keying at startup nor keying at any other time any troubleshooting suggestions thanks
Hilltoppers 40 not keying at startup nor keying at any other time any troubleshooting suggestions thanks
|
By
KM6KJE
· #19193
·
|
|
Wednesday Evening 40 and 80 meter Nets - Wed, 01/09/2019 8:00pm-9:00pm
#cal-reminder
I was putting in the 3.3 uH inductor and pulled the lead out of it (L1) so I replace it with a lesser tolerance. The one you sent me happens to be gold and the one I put in is silver. The gains contro
I was putting in the 3.3 uH inductor and pulled the lead out of it (L1) so I replace it with a lesser tolerance. The one you sent me happens to be gold and the one I put in is silver. The gains contro
|
By
KM6KJE
· #19003
·
|